-- extracted from draft-ietf-ospf-ospfv3-mib-11.txt
-- at Thu Aug 17 06:06:54 2006OSPFV3-MIB-JUNIPER DEFINITIONS::=BEGINIMPORTSMODULE-IDENTITY,OBJECT-TYPE,NOTIFICATION-TYPE, mib-2,Counter32,Gauge32,Integer32,Unsigned32FROM SNMPv2-SMI
TEXTUAL-CONVENTION,TruthValue,RowStatusFROM SNMPv2-TC
MODULE-COMPLIANCE,OBJECT-GROUP,NOTIFICATION-GROUPFROM SNMPv2-CONF
InterfaceIndexFROM IF-MIB
InetAddressType,InetAddress,InetAddressPrefixLengthFROM INET-ADDRESS-MIB
Metric,BigMetric,Status,HelloRange,DesignatedRouterPriorityFROM OSPF-MIB
-- Juniper specific *** JNX ***jnxOspfv3Experiment -- *** JNX ***FROM JUNIPER-EXPERIMENT-MIB -- *** JNX ***;jnxOspfv3MIB MODULE-IDENTITYLAST-UPDATED"200608091200Z"ORGANIZATION"IETF OSPF Working Group"CONTACT-INFO"WG E-Mail: ospf@ietf.org
WG Chairs: acee@cisco.com
dube.rohit@gmail.com
Dan Joyal
Nortel
600 Technology Park Drive
Billerica, MA 01821, USA
djoyal@nortel.com
Vishwas Manral
IP Infusion
Bangalore
India
vishwas@ipinfusion.com"DESCRIPTION"The MIB module for OSPF version 3.
Copyright (C) The Internet Society (2006).
This version of this MIB module is part of
RFC XXXX; see the RFC itself for full legal
notices."REVISION"200608091200Z"DESCRIPTION-- RFC Editor assigns RFC xxxx"Initial version, published as RFC xxxx"::={ jnxOspfv3Experiment 1}-- *** JNX ***-- Texual conventionsJnxOspfv3UpToRefreshIntervalTc ::=TEXTUAL-CONVENTIONDISPLAY-HINT"d"STATUScurrentDESCRIPTION"The values one might be able to configure for
variables bounded by the Refresh Interval"SYNTAXInteger32(1..1800)JnxOspfv3DeadIntRangeTc ::=TEXTUAL-CONVENTIONDISPLAY-HINT"d"STATUScurrentDESCRIPTION"The range, in seconds, of dead interval value."SYNTAXInteger32(1..'FFFF'h)JnxOspfv3RouterIdTc ::=TEXTUAL-CONVENTIONDISPLAY-HINT"d"STATUScurrentDESCRIPTION"A 32-bit, unsigned integer uniquely identifying the
router in the Autonomous System. To ensure uniqueness,
this may default to the value of one of the router's
IPv4 host addresses if IPv4 is configured on the
router."SYNTAXUnsigned32(1..4294967295)JnxOspfv3AreaIdTc ::=TEXTUAL-CONVENTIONDISPLAY-HINT"d"STATUScurrentDESCRIPTION"An OSPFv3 Area Identifier"SYNTAXUnsigned32(0..'FFFFFFFF'h)JnxOspfv3IfInstIdTc ::=TEXTUAL-CONVENTIONDISPLAY-HINT"d"STATUScurrentDESCRIPTION"An OSPFv3 interface instance ID"SYNTAXInteger32(0..255)-- Top-level structure of MIBjnxOspfv3Notifications OBJECTIDENTIFIER::={ jnxOspfv3MIB 0}jnxOspfv3Objects OBJECTIDENTIFIER::={ jnxOspfv3MIB 1}jnxOspfv3Conformance OBJECTIDENTIFIER::={ jnxOspfv3MIB 2}-- OSPFv3 General Variables-- These parameters apply globally to the Router's-- OSPFv3 Process.jnxOspfv3GeneralGroup OBJECTIDENTIFIER::={ jnxOspfv3Objects 1}jnxOspfv3RouterId OBJECT-TYPESYNTAX JnxOspfv3RouterIdTc
MAX-ACCESSread-writeSTATUScurrentDESCRIPTION"A 32-bit integer uniquely identifying the
router in the Autonomous System. To ensure
uniqueness, this may default to the value of
one of the router's IPv4 host addresses,
represented as a 32-bit unsigned integer,
if IPv4 is configured on the router."::={ jnxOspfv3GeneralGroup 1}jnxOspfv3AdminStat OBJECT-TYPESYNTAXStatusMAX-ACCESSread-writeSTATUScurrentDESCRIPTION"The administrative status of OSPFv3 in the
router. The value 'enabled' denotes that the
OSPFv3 Process is active on at least one
interface; 'disabled' disables it on all
interfaces."::={ jnxOspfv3GeneralGroup 2}jnxOspfv3VersionNumber OBJECT-TYPESYNTAXINTEGER{ version3 (3)}MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The version number of OSPF for IPv6 is 3."::={ jnxOspfv3GeneralGroup 3}jnxOspfv3AreaBdrRtrStatus OBJECT-TYPESYNTAXTruthValueMAX-ACCESSread-onlySTATUScurrentDESCRIPTION"A flag to note whether this router is an area
border router."REFERENCE"OSPF Version 2, Section 3 Splitting the AS into
Areas"::={ jnxOspfv3GeneralGroup 4}jnxOspfv3ASBdrRtrStatus OBJECT-TYPESYNTAXTruthValueMAX-ACCESSread-writeSTATUScurrentDESCRIPTION"A flag to note whether this router is
configured as an Autonomous System border router."REFERENCE"OSPF Version 2, Section 3.3 Classification of
routers"::={ jnxOspfv3GeneralGroup 5}jnxOspfv3AsScopeLsaCount OBJECT-TYPESYNTAXGauge32MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The number of AS-Scope (e.g. AS-External) link state
advertisements in the link state database."::={ jnxOspfv3GeneralGroup 6}jnxOspfv3AsScopeLsaCksumSum OBJECT-TYPESYNTAXInteger32MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The 32-bit unsigned sum of the LS checksums of
the AS-scoped link state advertisements
contained in the link state database. This sum
can be used to determine if there has been a
change in a router's link state database, and
to compare the link state database of two
routers."::={ jnxOspfv3GeneralGroup 7}jnxOspfv3OriginateNewLsas OBJECT-TYPESYNTAXCounter32MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The number of new link-state advertisements
that have been originated. This number is
incremented each time the router originates a new
LSA."::={ jnxOspfv3GeneralGroup 8}jnxOspfv3RxNewLsas OBJECT-TYPESYNTAXCounter32MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The number of link state advertisements
received determined to be new instantiations.
This number does not include newer
instantiations of self-originated link state
advertisements."::={ jnxOspfv3GeneralGroup 9}jnxOspfv3ExtLsaCount OBJECT-TYPESYNTAXGauge32MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The number of External(LS type 0x4005) in the
link state database"::={ jnxOspfv3GeneralGroup 10}jnxOspfv3ExtAreaLsdbLimit OBJECT-TYPESYNTAXInteger32(-1..'7FFFFFFF'h)MAX-ACCESSread-writeSTATUScurrentDESCRIPTION"The maximum number of non-default
AS-external-LSAs entries that can be stored in the
link state database. If the value is -1, then
there is no limit.
When the number of non-default AS-external-LSAs
in a router's link-state database reaches
ospfv3ExtAreaLsdbLimit, the router enters Overflow
state. The router never holds more than
ospfv3ExtAreaLsdbLimit non-default AS-external-LSAs
in its database. Ospfv3ExtAreaLsdbLimit MUST be set
identically in all routers attached to the OSPFv3
backbone and/or any regular OSPFv3 area. (i.e.,
OSPFv3 stub areas and NSSAs are excluded)."::={ jnxOspfv3GeneralGroup 11}jnxOspfv3MulticastExtensions OBJECT-TYPESYNTAXBITS{intraAreaMulticast(0),interAreaMulticast(1),interAsMulticast(2)}MAX-ACCESSread-writeSTATUScurrentDESCRIPTION"A Bit Mask indicating whether the router is
forwarding IPv6 multicast datagrams based on
the algorithms defined in the Multicast
Extensions to OSPF.
If intraAreaMulticast set, indicates that the router
can forward IPv6 multicast datagrams in the router's
directly attached areas (called intra-area
multicast routing).
If interAreaMulticast set, indicates that the router
can forward IPv6 multicast datagrams between OSPFv3
areas (called inter-area multicast routing).
If interAsMulticast set, indicates that the router can
forward IPv6 multicast datagrams between
Autonomous Systems (called inter-AS multicast
routing).
Only certain combinations of bit settings are
allowed, namely:
- All bits cleared (no multicasting)
- intraAreaMulticast only,
- intraAreaMulticast and interAreaMulticast,
- intraAreaMulticast and interAsMulticast
- intraAreaMulticast, interAreaMulticast and
interAsMulticast
By default, all bits are cleared."::={ jnxOspfv3GeneralGroup 12}jnxOspfv3ExitOverflowInterval OBJECT-TYPESYNTAXUnsigned32UNITS"seconds"MAX-ACCESSread-writeSTATUScurrentDESCRIPTION"The number of seconds that, after entering
Overflow State, a router will attempt to leave
Overflow State. This allows the router to again
originate non-default, AS-External-LSAs. When
set to 0, the router will not leave Overflow
State until restarted."::={ jnxOspfv3GeneralGroup 13}jnxOspfv3DemandExtensions OBJECT-TYPESYNTAXTruthValueMAX-ACCESSread-writeSTATUScurrentDESCRIPTION"The router's support for demand routing."REFERENCE"Ospf Version 2, Appendix on Demand Routing"::={ jnxOspfv3GeneralGroup 14}jnxOspfv3ReferenceBandwidth OBJECT-TYPESYNTAXUnsigned32MAX-ACCESSread-writeSTATUScurrentDESCRIPTION"Reference bandwidth in kilobits/second for
calculating default interface metrics. The
default value is 100,000 KBPS (100 MBPS)"::={ jnxOspfv3GeneralGroup 15}jnxOspfv3RestartSupport OBJECT-TYPESYNTAXINTEGER{ none (1),plannedOnly (2),plannedAndUnplanned (3)}MAX-ACCESSread-writeSTATUScurrentDESCRIPTION"The router's support for OSPF Graceful restart.
Options include: no restart support, only planned
restarts or both planned and unplanned restarts."::={ jnxOspfv3GeneralGroup 16}jnxOspfv3RestartInterval OBJECT-TYPESYNTAX JnxOspfv3UpToRefreshIntervalTc
UNITS"seconds"MAX-ACCESSread-writeSTATUScurrentDESCRIPTION"Configured OSPF Graceful restart timeout interval."::={ jnxOspfv3GeneralGroup 17}jnxOspfv3RestartStatus OBJECT-TYPESYNTAXINTEGER{ notRestarting (1),plannedRestart (2),unplannedRestart (3)}MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The current status of OSPF Graceful restart capability."::={ jnxOspfv3GeneralGroup 18}jnxOspfv3RestartAge OBJECT-TYPESYNTAX JnxOspfv3UpToRefreshIntervalTc
UNITS"seconds"MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"Remaining time in current OSPF Graceful restart
interval."::={ jnxOspfv3GeneralGroup 19}jnxOspfv3RestartExitRc OBJECT-TYPESYNTAXINTEGER{ none (1),inProgress (2),completed (3),timedOut (4),topologyChanged (5)}MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"Describes the outcome of the last attempt at a
Graceful restart.
none:............no restart has yet been attempted.
inProgress:......a restart attempt is currently underway.
completed:.......the last restart completed successfully.
timedOut:........the last restart timed out.
topologyChanged:.the last restart was aborted due to
a topology change."::={ jnxOspfv3GeneralGroup 20}jnxOspfv3NotificationEnable OBJECT-TYPESYNTAXTruthValueMAX-ACCESSread-writeSTATUScurrentDESCRIPTION"If this object is set to true(1), then it enables
the generation of OSPFv3 Notifications. If it is
set to false(2), these notifications are not
generated.
Configured values MUST survive an agent reboot."DEFVAL{ true }::={ jnxOspfv3GeneralGroup 21}-- The OSPFv3 Area Data Structure contains information-- regarding the various areas. The interfaces and-- virtual links are configured as part of these areas.-- Area 0, by definition, is the Backbone AreajnxOspfv3AreaTable OBJECT-TYPESYNTAXSEQUENCEOF JnxOspfv3AreaEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"Information describing the configured
parameters and cumulative statistics of the router's
attached areas."REFERENCE"OSPF Version 2, Section 6 The Area Data
Structure"::={ jnxOspfv3Objects 2}jnxOspfv3AreaEntry OBJECT-TYPESYNTAX JnxOspfv3AreaEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"Information describing the configured
parameters and cumulative statistics of one of the
router's attached areas."INDEX{ jnxOspfv3AreaId }::={ jnxOspfv3AreaTable 1}
JnxOspfv3AreaEntry ::=SEQUENCE{
jnxOspfv3AreaId
JnxOspfv3AreaIdTc,
jnxOspfv3ImportAsExtern
INTEGER,
jnxOspfv3AreaSpfRuns
Counter32,
jnxOspfv3AreaBdrRtrCount
Gauge32,
jnxOspfv3AreaAsBdrRtrCount
Gauge32,
jnxOspfv3AreaScopeLsaCount
Gauge32,
jnxOspfv3AreaScopeLsaCksumSum
Integer32,
jnxOspfv3AreaSummary
INTEGER,
jnxOspfv3AreaStatus
RowStatus,
jnxOspfv3StubMetric
BigMetric,
jnxOspfv3AreaNssaTranslatorRole
INTEGER,
jnxOspfv3AreaNssaTranslatorState
INTEGER,
jnxOspfv3AreaNssaTranslatorStabInt
Unsigned32,
jnxOspfv3AreaNssaTranslatorEvents
Counter32,
jnxOspfv3AreaStubMetricType
INTEGER}jnxOspfv3AreaId OBJECT-TYPESYNTAX JnxOspfv3AreaIdTc
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"A 32-bit integer uniquely identifying an area.
Area ID 0 is used for the OSPFv3 backbone."REFERENCE"OSPF Version 2, Appendix C.2 Area parameters"::={ jnxOspfv3AreaEntry 1}jnxOspfv3ImportAsExtern OBJECT-TYPESYNTAXINTEGER{importExternal(1),-- normal areaimportNoExternal(2),-- stub area
importNssa(3)-- not-so-stubby-area}MAX-ACCESSread-createSTATUScurrentDESCRIPTION"Indicates whether an area is a Stub area, NSSA, or
standard area. AS-scope LSAs are not imported into Stub
Areas or NSSAs. NSSAs import AS-External data as NSSA
LSAs which have Area-scope"REFERENCE"OSPF Version 2, Appendix C.2 Area parameters"DEFVAL{ importExternal }::={ jnxOspfv3AreaEntry 2}jnxOspfv3AreaSpfRuns OBJECT-TYPESYNTAXCounter32MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The number of times that the intra-area route
table has been calculated using this area's
link state database. This is typically done
using Dijkstra's algorithm."::={ jnxOspfv3AreaEntry 3}jnxOspfv3AreaBdrRtrCount OBJECT-TYPESYNTAXGauge32MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The total number of area border routers
reachable within this area. This is initially zero,
and is calculated in each SPF Pass."::={ jnxOspfv3AreaEntry 4}jnxOspfv3AreaAsBdrRtrCount OBJECT-TYPESYNTAXGauge32MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The total number of Autonomous System border
routers reachable within this area. This is
initially zero, and is calculated in each SPF
Pass."::={ jnxOspfv3AreaEntry 5}jnxOspfv3AreaScopeLsaCount OBJECT-TYPESYNTAXGauge32MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The total number of Area-Scope link state
advertisements in this area's link state
database."::={ jnxOspfv3AreaEntry 6}jnxOspfv3AreaScopeLsaCksumSum OBJECT-TYPESYNTAXInteger32MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The 32-bit unsigned sum of the Area-Scope link state
advertisements' LS checksums contained in this
area's link state database. The sum can be used
to determine if there has been a change in a
router's link state database, and to compare the
link-state database of two routers."::={ jnxOspfv3AreaEntry 7}jnxOspfv3AreaSummary OBJECT-TYPESYNTAXINTEGER{noAreaSummary(1),sendAreaSummary(2)}MAX-ACCESSread-createSTATUScurrentDESCRIPTION"The variable ospfv3AreaSummary controls the
import of Inter-Area LSAs into stub and
NSSA areas. It has no effect on other areas.
If it is noAreaSummary, the router will neither
originate nor propagate Inter-Area LSAs into the
stub or NSSA area. It will rely entirely on its
default route.
If it is sendAreaSummary, the router will both
summarize and propagate Inter-Area LSAs."DEFVAL{ sendAreaSummary }::={ jnxOspfv3AreaEntry 8}jnxOspfv3AreaStatus OBJECT-TYPESYNTAXRowStatusMAX-ACCESSread-createSTATUScurrentDESCRIPTION"This object permits management of the table by
facilitating actions such as row creation,
construction and destruction.
The value of this object has no effect on
whether other objects in this conceptual row can be
modified."::={ jnxOspfv3AreaEntry 9}jnxOspfv3StubMetric OBJECT-TYPESYNTAXBigMetricMAX-ACCESSread-createSTATUScurrentDESCRIPTION"The metric value advertised for the default route
into Stub and NSSA areas."::={ jnxOspfv3AreaEntry 10}jnxOspfv3AreaNssaTranslatorRole OBJECT-TYPESYNTAXINTEGER{ always(1), candidate(2)}MAX-ACCESSread-createSTATUScurrentDESCRIPTION"Indicates an NSSA Border router's ability to
perform NSSA translation of NSSA-LSAs into
AS-External-LSAs."DEFVAL{ candidate }::={ jnxOspfv3AreaEntry 11}jnxOspfv3AreaNssaTranslatorState OBJECT-TYPESYNTAXINTEGER{enabled(1),elected(2),disabled(3)}MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"Indicates if and how an NSSA Border router is
performing NSSA translation of NSSA-LSAs into
AS-External-LSA's. When this object is set to enabled,
the NSSA Border router's ospfv3AreaNssTranslatorRole
has been set to always. When this object is set to
elected, a candidate NSSA Border router is translating
NSSA-LSA's into AS-External-LSA's. When this object is
set to disabled, a candidate NSSA Border router is NOT
translating NSSA-LSA's into AS-External-LSA's."::={ jnxOspfv3AreaEntry 12}jnxOspfv3AreaNssaTranslatorStabInt OBJECT-TYPESYNTAXUnsigned32UNITS"seconds"MAX-ACCESSread-createSTATUScurrentDESCRIPTION"The number of seconds after an elected translator
determines its services are no longer required, that
it should continue to perform its translation duties."DEFVAL{40}::={ jnxOspfv3AreaEntry 13}jnxOspfv3AreaNssaTranslatorEvents OBJECT-TYPESYNTAXCounter32MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"Indicates the number of Translator State changes
that have occurred since the last boot-up."::={ jnxOspfv3AreaEntry 14}jnxOspfv3AreaStubMetricType OBJECT-TYPESYNTAXINTEGER{ospfv3Metric (1),-- OSPF MetriccomparableCost (2),-- external type 1nonComparable (3)-- external type 2}MAX-ACCESSread-createSTATUScurrentDESCRIPTION"This variable displays the type of metric
advertised as a default route."DEFVAL{ ospfv3Metric }::={ jnxOspfv3AreaEntry 15}-- OSPFv3 AS-Scope Link State Database-- The Link State Database contains the AS-Scope Link State-- Advertisements from throughout the areas that the-- device is attached to.jnxOspfv3AsLsdbTable OBJECT-TYPESYNTAXSEQUENCEOF JnxOspfv3AsLsdbEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"The OSPFv3 Process's AS-Scope Link State Database."::={ jnxOspfv3Objects 3}jnxOspfv3AsLsdbEntry OBJECT-TYPESYNTAX JnxOspfv3AsLsdbEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"A single AS-Scope Link State Advertisement."INDEX{ jnxOspfv3AsLsdbType,
jnxOspfv3AsLsdbRouterId,
jnxOspfv3AsLsdbLsid }::={ jnxOspfv3AsLsdbTable 1}
JnxOspfv3AsLsdbEntry ::=SEQUENCE{
jnxOspfv3AsLsdbType
Unsigned32,
jnxOspfv3AsLsdbRouterId
JnxOspfv3RouterIdTc,
jnxOspfv3AsLsdbLsid
Unsigned32,
jnxOspfv3AsLsdbSequence
Integer32,
jnxOspfv3AsLsdbAge
Integer32,
jnxOspfv3AsLsdbChecksum
Integer32,
jnxOspfv3AsLsdbAdvertisement
OCTETSTRING,
jnxOspfv3AsLsdbTypeKnown
TruthValue}jnxOspfv3AsLsdbType OBJECT-TYPESYNTAXUnsigned32(0..'FFFFFFFF'h)MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"The type of the link state advertisement.
Each link state type has a separate
advertisement format. AS-Scope LSAs not recognized
by the router may be stored in the database."::={ jnxOspfv3AsLsdbEntry 1}jnxOspfv3AsLsdbRouterId OBJECT-TYPESYNTAX JnxOspfv3RouterIdTc
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"The 32 bit number that uniquely identifies the
originating router in the Autonomous System."REFERENCE"OSPF Version 2, Appendix C.1 Global parameters"::={ jnxOspfv3AsLsdbEntry 2}jnxOspfv3AsLsdbLsid OBJECT-TYPESYNTAXUnsigned32MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"The Link State ID is an LS Type Specific field
containing a unique identifier;
it identifies the piece of the routing domain
that is being described by the advertisement.
In contrast to OSPFv2, the LSID has no
addressing semantics."::={ jnxOspfv3AsLsdbEntry 3}-- Note that the OSPF Sequence Number is a 32 bit signed-- integer. It starts with the value '80000001'h,-- or -'7FFFFFFF'h, and increments until '7FFFFFFF'h-- Thus, a typical sequence number will be very negative.jnxOspfv3AsLsdbSequence OBJECT-TYPESYNTAXInteger32MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The sequence number field is a signed 32-bit
integer. It is used to detect old and duplicate
link state advertisements. The space of
sequence numbers is linearly ordered. The
larger the sequence number the more recent the
advertisement."REFERENCE"OSPF Version 2, Section 12.1.6 LS sequence
number"::={ jnxOspfv3AsLsdbEntry 4}jnxOspfv3AsLsdbAge OBJECT-TYPESYNTAXInteger32-- Should be 0..MaxAge-- unless DoNotAge bit is setUNITS"seconds"MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This field is the age of the link state
advertisement in seconds."REFERENCE"OSPF Version 2, Section 12.1.1 LS age"::={ jnxOspfv3AsLsdbEntry 5}jnxOspfv3AsLsdbChecksum OBJECT-TYPESYNTAXInteger32MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This field is the checksum of the complete
contents of the advertisement, excepting the
age field. The age field is excepted so that
an advertisement's age can be incremented
without updating the checksum. The checksum
used is the same that is used for ISO
connectionless datagrams; it is commonly
referred to as the Fletcher checksum."REFERENCE"OSPF Version 2, Section 12.1.7 LS checksum"::={ jnxOspfv3AsLsdbEntry 6}jnxOspfv3AsLsdbAdvertisement OBJECT-TYPESYNTAXOCTETSTRING(SIZE(1..65535))MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The entire Link State Advertisement, including
its header."::={ jnxOspfv3AsLsdbEntry 7}jnxOspfv3AsLsdbTypeKnown OBJECT-TYPESYNTAXTruthValueMAX-ACCESSread-onlySTATUScurrentDESCRIPTION"Indicates whether the LSA type is recognized by
this Router."::={ jnxOspfv3AsLsdbEntry 8}-- OSPFv3 Area-Scope Link State Database-- The Link State Database contains the Area-Scope Link State-- Advertisements from throughout the area that the-- device is attached to.jnxOspfv3AreaLsdbTable OBJECT-TYPESYNTAXSEQUENCEOF JnxOspfv3AreaLsdbEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"The OSPFv3 Process's Area-Scope Link State Database."::={ jnxOspfv3Objects 4}jnxOspfv3AreaLsdbEntry OBJECT-TYPESYNTAX JnxOspfv3AreaLsdbEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"A single Area-Scope Link State Advertisement."INDEX{ jnxOspfv3AreaLsdbAreaId,
jnxOspfv3AreaLsdbType,
jnxOspfv3AreaLsdbRouterId,
jnxOspfv3AreaLsdbLsid }::={ jnxOspfv3AreaLsdbTable 1}
JnxOspfv3AreaLsdbEntry ::=SEQUENCE{
jnxOspfv3AreaLsdbAreaId
JnxOspfv3AreaIdTc,
jnxOspfv3AreaLsdbType
Unsigned32,
jnxOspfv3AreaLsdbRouterId
JnxOspfv3RouterIdTc,
jnxOspfv3AreaLsdbLsid
Unsigned32,
jnxOspfv3AreaLsdbSequence
Integer32,
jnxOspfv3AreaLsdbAge
Integer32,
jnxOspfv3AreaLsdbChecksum
Integer32,
jnxOspfv3AreaLsdbAdvertisement
OCTETSTRING,
jnxOspfv3AreaLsdbTypeKnown
TruthValue}jnxOspfv3AreaLsdbAreaId OBJECT-TYPESYNTAX JnxOspfv3AreaIdTc
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"The 32-bit identifier of the Area from which the
LSA was received."REFERENCE"OSPF Version 2, Appendix C.2 Area parameters"::={ jnxOspfv3AreaLsdbEntry 1}jnxOspfv3AreaLsdbType OBJECT-TYPESYNTAXUnsigned32(0..'FFFFFFFF'h)MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"The type of the link state advertisement.
Each link state type has a separate
advertisement format. Area-Scope LSAs unrecognized
by the router are also stored in this database."::={ jnxOspfv3AreaLsdbEntry 2}jnxOspfv3AreaLsdbRouterId OBJECT-TYPESYNTAX JnxOspfv3RouterIdTc
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"The 32-bit number that uniquely identifies the
originating router in the Autonomous System."REFERENCE"OSPF Version 2, Appendix C.1 Global parameters"::={ jnxOspfv3AreaLsdbEntry 3}jnxOspfv3AreaLsdbLsid OBJECT-TYPESYNTAXUnsigned32MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"The Link State ID is an LS Type Specific field
containing a unique identifier;
it identifies the piece of the routing domain
that is being described by the advertisement.
In contrast to OSPFv2, the LSID has no
addressing semantics."::={ jnxOspfv3AreaLsdbEntry 4}-- Note that the OSPF Sequence Number is a 32 bit signed-- integer. It starts with the value '80000001'h,-- or -'7FFFFFFF'h, and increments until '7FFFFFFF'h-- Thus, a typical sequence number will be very negative.jnxOspfv3AreaLsdbSequence OBJECT-TYPESYNTAXInteger32MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The sequence number field is a signed 32-bit
integer. It is used to detect old and
duplicate link state advertisements. The space
of sequence numbers is linearly ordered. The
larger the sequence number the more recent the
advertisement."REFERENCE"OSPF Version 2, Section 12.1.6 LS sequence
number"::={ jnxOspfv3AreaLsdbEntry 5}jnxOspfv3AreaLsdbAge OBJECT-TYPESYNTAXInteger32-- Should be 0..MaxAge-- unless DoNotAge bit is setUNITS"seconds"MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This field is the age of the link state
advertisement in seconds."REFERENCE"OSPF Version 2, Section 12.1.1 LS age"::={ jnxOspfv3AreaLsdbEntry 6}jnxOspfv3AreaLsdbChecksum OBJECT-TYPESYNTAXInteger32MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This field is the checksum of the complete
contents of the advertisement, excepting the
age field. The age field is excepted so that
an advertisement's age can be incremented
without updating the checksum. The checksum
used is the same that is used for ISO
connectionless datagrams; it is commonly
referred to as the Fletcher checksum."REFERENCE"OSPF Version 2, Section 12.1.7 LS checksum"::={ jnxOspfv3AreaLsdbEntry 7}jnxOspfv3AreaLsdbAdvertisement OBJECT-TYPESYNTAXOCTETSTRING(SIZE(1..65535))MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The entire Link State Advertisement, including
its header."::={ jnxOspfv3AreaLsdbEntry 8}jnxOspfv3AreaLsdbTypeKnown OBJECT-TYPESYNTAXTruthValueMAX-ACCESSread-onlySTATUScurrentDESCRIPTION"Indicates whether the LSA type is recognized
by this Router."::={ jnxOspfv3AreaLsdbEntry 9}-- Ospfv3 Link-Scope Link State Database-- The Link State Database contains the Link-Scope Link State-- Advertisements from the links that the-- device is attached to.jnxOspfv3LinkLsdbTable OBJECT-TYPESYNTAXSEQUENCEOF JnxOspfv3LinkLsdbEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"The OSPFv3 Process's Link-Scope Link State Database."::={ jnxOspfv3Objects 5}jnxOspfv3LinkLsdbEntry OBJECT-TYPESYNTAX JnxOspfv3LinkLsdbEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"A single Link-Scope Link State Advertisement."INDEX{ jnxOspfv3LinkLsdbIfIndex,
jnxOspfv3LinkLsdbIfInstId,
jnxOspfv3LinkLsdbType,
jnxOspfv3LinkLsdbRouterId,
jnxOspfv3LinkLsdbLsid }::={ jnxOspfv3LinkLsdbTable 1}
JnxOspfv3LinkLsdbEntry ::=SEQUENCE{
jnxOspfv3LinkLsdbIfIndex
InterfaceIndex,
jnxOspfv3LinkLsdbIfInstId
JnxOspfv3IfInstIdTc,
jnxOspfv3LinkLsdbType
Unsigned32,
jnxOspfv3LinkLsdbRouterId
JnxOspfv3RouterIdTc,
jnxOspfv3LinkLsdbLsid
Unsigned32,
jnxOspfv3LinkLsdbSequence
Integer32,
jnxOspfv3LinkLsdbAge
Integer32,
jnxOspfv3LinkLsdbChecksum
Integer32,
jnxOspfv3LinkLsdbAdvertisement
OCTETSTRING,
jnxOspfv3LinkLsdbTypeKnown
TruthValue}jnxOspfv3LinkLsdbIfIndex OBJECT-TYPESYNTAXInterfaceIndexMAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"The identifier of the link from which the LSA
was received."::={ jnxOspfv3LinkLsdbEntry 1}jnxOspfv3LinkLsdbIfInstId OBJECT-TYPESYNTAX JnxOspfv3IfInstIdTc
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"The identifier of the interface instance from
which the LSA was received."::={ jnxOspfv3LinkLsdbEntry 2}jnxOspfv3LinkLsdbType OBJECT-TYPESYNTAXUnsigned32(0..'FFFFFFFF'h)MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"The type of the link state advertisement.
Each link state type has a separate
advertisement format. Link-Scope LSAs unrecognized
by the router are also stored in this database."::={ jnxOspfv3LinkLsdbEntry 3}jnxOspfv3LinkLsdbRouterId OBJECT-TYPESYNTAX JnxOspfv3RouterIdTc
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"The 32 bit number that uniquely identifies the
originating router in the Autonomous System."REFERENCE"OSPF Version 2, Appendix C.1 Global parameters"::={ jnxOspfv3LinkLsdbEntry 4}jnxOspfv3LinkLsdbLsid OBJECT-TYPESYNTAXUnsigned32MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"The Link State ID is an LS Type Specific field
containing a unique identifier;
it identifies the piece of the routing domain
that is being described by the advertisement.
In contrast to OSPFv2, the LSID has no
addressing semantics."::={ jnxOspfv3LinkLsdbEntry 5}-- Note that the OSPF Sequence Number is a 32 bit signed-- integer. It starts with the value '80000001'h,-- or -'7FFFFFFF'h, and increments until '7FFFFFFF'h-- Thus, a typical sequence number will be very negative.jnxOspfv3LinkLsdbSequence OBJECT-TYPESYNTAXInteger32MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The sequence number field is a signed 32-bit
integer. It is used to detect old and duplicate
link state advertisements. The space of
sequence numbers is linearly ordered. The
larger the sequence number the more recent the
advertisement."REFERENCE"OSPF Version 2, Section 12.1.6 LS sequence
number"::={ jnxOspfv3LinkLsdbEntry 6}jnxOspfv3LinkLsdbAge OBJECT-TYPESYNTAXInteger32-- Should be 0..MaxAge-- unless DoNotAge bit is setUNITS"seconds"MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This field is the age of the link state
advertisement in seconds."REFERENCE"OSPF Version 2, Section 12.1.1 LS age"::={ jnxOspfv3LinkLsdbEntry 7}jnxOspfv3LinkLsdbChecksum OBJECT-TYPESYNTAXInteger32MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This field is the checksum of the complete
contents of the advertisement, excepting the
age field. The age field is excepted so that
an advertisement's age can be incremented
without updating the checksum. The checksum
used is the same that is used for ISO
connectionless datagrams; it is commonly
referred to as the Fletcher checksum."REFERENCE"OSPF Version 2, Section 12.1.7 LS checksum"::={ jnxOspfv3LinkLsdbEntry 8}jnxOspfv3LinkLsdbAdvertisement OBJECT-TYPESYNTAXOCTETSTRING(SIZE(1..65535))MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The entire Link State Advertisement, including
its header."::={ jnxOspfv3LinkLsdbEntry 9}jnxOspfv3LinkLsdbTypeKnown OBJECT-TYPESYNTAXTruthValueMAX-ACCESSread-onlySTATUScurrentDESCRIPTION"Indicates whether the LSA type is recognized by this
Router."::={ jnxOspfv3LinkLsdbEntry 10}-- OSPF Host Table-- The Host/Metric Table indicates what hosts are directly-- attached to the Router, and what metrics and types of-- service should be advertised for them.jnxOspfv3HostTable OBJECT-TYPESYNTAXSEQUENCEOF JnxOspfv3HostEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"The list of Hosts, and their metrics, that the
router will advertise as host routes."REFERENCE"OSPF Version 2, Appendix C.6 Host route
parameters"::={ jnxOspfv3Objects 6}jnxOspfv3HostEntry OBJECT-TYPESYNTAX JnxOspfv3HostEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"A metric to be advertised when a given host is
reachable."INDEX{ jnxOspfv3HostAddressType,
jnxOspfv3HostAddress }::={ jnxOspfv3HostTable 1}
JnxOspfv3HostEntry ::=SEQUENCE{
jnxOspfv3HostAddressType
InetAddressType,
jnxOspfv3HostAddress
InetAddress,
jnxOspfv3HostMetric
Metric,
jnxOspfv3HostStatus
RowStatus,
jnxOspfv3HostAreaID
JnxOspfv3AreaIdTc
}jnxOspfv3HostAddressType OBJECT-TYPESYNTAXInetAddressTypeMAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"The address type of ospfv3HostAddress. Only IPv6
addresses without zone index are expected."REFERENCE"OSPF Version 2, Appendix C.6 Host route
parameters"::={ jnxOspfv3HostEntry 1}jnxOspfv3HostAddress OBJECT-TYPESYNTAXInetAddress(SIZE(16))MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"The IPv6 Address of the Host. Must be a Global
address."REFERENCE"OSPF Version 2, Appendix C.6 Host route
parameters"::={ jnxOspfv3HostEntry 2}jnxOspfv3HostMetric OBJECT-TYPESYNTAXMetricMAX-ACCESSread-createSTATUScurrentDESCRIPTION"The Metric to be advertised."REFERENCE"OSPF Version 2, Appendix C.6 Host route
parameters"::={ jnxOspfv3HostEntry 3}jnxOspfv3HostStatus OBJECT-TYPESYNTAXRowStatusMAX-ACCESSread-createSTATUScurrentDESCRIPTION"This object permits management of the table by
facilitating actions such as row creation,
construction and destruction.
The value of this object has no effect on
whether other objects in this conceptual row can be
modified."::={ jnxOspfv3HostEntry 4}jnxOspfv3HostAreaID OBJECT-TYPESYNTAX JnxOspfv3AreaIdTc
MAX-ACCESSread-createSTATUScurrentDESCRIPTION"The Area the Host Entry is to be found within.
By default, the area that a subsuming OSPFv3
interface is in, or Area 0"REFERENCE"OSPF Version 2, Appendix C.2 Area parameters"::={ jnxOspfv3HostEntry 5}-- OSPFv3 Interface TablejnxOspfv3IfTable OBJECT-TYPESYNTAXSEQUENCEOF JnxOspfv3IfEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"The OSPFv3 Interface Table describes the
interfaces from the viewpoint of OSPFv3."REFERENCE"OSPF Version 2, Appendix C.3 Router interface
parameters"::={ jnxOspfv3Objects 7}jnxOspfv3IfEntry OBJECT-TYPESYNTAX JnxOspfv3IfEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"The OSPFv3 Interface Entry describes one
interface from the viewpoint of OSPFv3."INDEX{ jnxOspfv3IfIndex,
jnxOspfv3IfInstId }::={ jnxOspfv3IfTable 1}
JnxOspfv3IfEntry ::=SEQUENCE{
jnxOspfv3IfIndex
InterfaceIndex,
jnxOspfv3IfInstId
JnxOspfv3IfInstIdTc,
jnxOspfv3IfAreaId
JnxOspfv3AreaIdTc,
jnxOspfv3IfType
INTEGER,
jnxOspfv3IfAdminStat
Status,
jnxOspfv3IfRtrPriority
DesignatedRouterPriority,
jnxOspfv3IfTransitDelay
JnxOspfv3UpToRefreshIntervalTc,
jnxOspfv3IfRetransInterval
JnxOspfv3UpToRefreshIntervalTc,
jnxOspfv3IfHelloInterval
HelloRange,
jnxOspfv3IfRtrDeadInterval
JnxOspfv3DeadIntRangeTc,
jnxOspfv3IfPollInterval
Unsigned32,
jnxOspfv3IfState
INTEGER,
jnxOspfv3IfDesignatedRouter
JnxOspfv3RouterIdTc,
jnxOspfv3IfBackupDesignatedRouter
JnxOspfv3RouterIdTc,
jnxOspfv3IfEvents
Counter32,
jnxOspfv3IfStatus
RowStatus,
jnxOspfv3IfMulticastForwarding
INTEGER,
jnxOspfv3IfDemand
TruthValue,
jnxOspfv3IfMetricValue
Metric,
jnxOspfv3IfLinkScopeLsaCount
Gauge32,
jnxOspfv3IfLinkLsaCksumSum
Integer32,
jnxOspfv3IfDemandNbrProbe
TruthValue,
jnxOspfv3IfDemandNbrProbeRetxLimit
Unsigned32,
jnxOspfv3IfDemandNbrProbeInterval
Unsigned32}jnxOspfv3IfIndex OBJECT-TYPESYNTAXInterfaceIndexMAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"The interface index of this OSPFv3 interface.
It corresponds to the interface index of the
IPv6 interface on which OSPFv3 is configured."::={ jnxOspfv3IfEntry 1}jnxOspfv3IfInstId OBJECT-TYPESYNTAX JnxOspfv3IfInstIdTc
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"Enables multiple interface instances of OSPFv3
to be run over a single link. Each protocol
instance would be assigned a separate ID. This ID
has local link significance only."::={ jnxOspfv3IfEntry 2}jnxOspfv3IfAreaId OBJECT-TYPESYNTAX JnxOspfv3AreaIdTc
MAX-ACCESSread-createSTATUScurrentDESCRIPTION"A 32-bit integer uniquely identifying the area
to which the interface connects. Area ID
0 is used for the OSPFv3 backbone."DEFVAL{0}::={ jnxOspfv3IfEntry 3}jnxOspfv3IfType OBJECT-TYPESYNTAXINTEGER{broadcast(1),nbma(2),pointToPoint(3),pointToMultipoint(5)}MAX-ACCESSread-createSTATUScurrentDESCRIPTION"The OSPFv3 interface type."::={ jnxOspfv3IfEntry 4}jnxOspfv3IfAdminStat OBJECT-TYPESYNTAXStatusMAX-ACCESSread-createSTATUScurrentDESCRIPTION"The OSPFv3 interface's administrative status.
The value formed on the interface, and the
interface will be advertised as an internal route
to some area. The value 'disabled' denotes
that the interface is external to OSPFv3."DEFVAL{ enabled }::={ jnxOspfv3IfEntry 5}jnxOspfv3IfRtrPriority OBJECT-TYPESYNTAXDesignatedRouterPriorityMAX-ACCESSread-createSTATUScurrentDESCRIPTION"The priority of this interface. Used in
multi-access networks, this field is used in
the designated router election algorithm. The
value 0 signifies that the router is not
eligible to become the designated router on this
particular network. In the event of a tie in
this value, routers will use their Router ID as
a tie breaker."DEFVAL{1}::={ jnxOspfv3IfEntry 6}jnxOspfv3IfTransitDelay OBJECT-TYPESYNTAX JnxOspfv3UpToRefreshIntervalTc
UNITS"seconds"MAX-ACCESSread-createSTATUScurrentDESCRIPTION"The estimated number of seconds it takes to
transmit a link state update packet over this
interface."DEFVAL{1}::={ jnxOspfv3IfEntry 7}jnxOspfv3IfRetransInterval OBJECT-TYPESYNTAX JnxOspfv3UpToRefreshIntervalTc
UNITS"seconds"MAX-ACCESSread-createSTATUScurrentDESCRIPTION"The number of seconds between link state
advertisement retransmissions, for adjacencies
belonging to this interface. This value is
also used when retransmitting database
description and link state request packets."DEFVAL{5}::={ jnxOspfv3IfEntry 8}jnxOspfv3IfHelloInterval OBJECT-TYPESYNTAXHelloRangeUNITS"seconds"MAX-ACCESSread-createSTATUScurrentDESCRIPTION"The length of time, in seconds, between the
Hello packets that the router sends on the
interface. This value must be the same for all
routers attached to a common network."DEFVAL{10}::={ jnxOspfv3IfEntry 9}jnxOspfv3IfRtrDeadInterval OBJECT-TYPESYNTAX JnxOspfv3DeadIntRangeTc
UNITS"seconds"MAX-ACCESSread-createSTATUScurrentDESCRIPTION"The number of seconds that a router's Hello
packets have not been seen before its
neighbors declare the router down on the interface.
This should be some multiple of the Hello interval.
This value must be the same for all routers attached
to a common network."DEFVAL{40}::={ jnxOspfv3IfEntry 10}jnxOspfv3IfPollInterval OBJECT-TYPESYNTAXUnsigned32UNITS"seconds"MAX-ACCESSread-createSTATUScurrentDESCRIPTION"The larger time interval, in seconds, between
the Hello packets sent to an inactive
non-broadcast multi-access neighbor."DEFVAL{120}::={ jnxOspfv3IfEntry 11}jnxOspfv3IfState OBJECT-TYPESYNTAXINTEGER{down(1),loopback(2),waiting(3),pointToPoint(4),designatedRouter(5),backupDesignatedRouter(6),otherDesignatedRouter(7)}MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The OSPFv3 Interface State."::={ jnxOspfv3IfEntry 12}jnxOspfv3IfDesignatedRouter OBJECT-TYPESYNTAX JnxOspfv3RouterIdTc
MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The Router ID of the Designated Router."::={ jnxOspfv3IfEntry 13}jnxOspfv3IfBackupDesignatedRouter OBJECT-TYPESYNTAX JnxOspfv3RouterIdTc
MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The Router ID of the Backup Designated
Router."::={ jnxOspfv3IfEntry 14}jnxOspfv3IfEvents OBJECT-TYPESYNTAXCounter32MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The number of times this OSPF interface has
changed its state, or an error has occurred."::={ jnxOspfv3IfEntry 15}jnxOspfv3IfStatus OBJECT-TYPESYNTAXRowStatusMAX-ACCESSread-createSTATUScurrentDESCRIPTION"This object permits management of the table by
facilitating actions such as row creation,
construction and destruction.
The value of this object has no effect on
whether other objects in this conceptual row can be
modified."::={ jnxOspfv3IfEntry 16}jnxOspfv3IfMulticastForwarding OBJECT-TYPESYNTAXINTEGER{blocked(1),-- no multicast forwardingmulticast(2),-- using multicast addressunicast(3)-- to each OSPFv3 neighbor}MAX-ACCESSread-createSTATUScurrentDESCRIPTION"The way multicasts should forwarded on this
interface; not forwarded, forwarded as data
link multicasts, or forwarded as data link
unicasts. Data link multicasting is not
meaningful on point to point and NBMA interfaces,
and setting ospfv3MulticastForwarding to 0
effectively disables all multicast forwarding."DEFVAL{ blocked }::={ jnxOspfv3IfEntry 17}jnxOspfv3IfDemand OBJECT-TYPESYNTAXTruthValueMAX-ACCESSread-createSTATUScurrentDESCRIPTION"Indicates whether Demand OSPFv3 procedures
(hello suppression to FULL neighbors and
setting the DoNotAge flag on propagated LSAs)
should be performed on this interface."DEFVAL{ false }::={ jnxOspfv3IfEntry 18}jnxOspfv3IfMetricValue OBJECT-TYPESYNTAXMetricMAX-ACCESSread-createSTATUScurrentDESCRIPTION"The metric assigned to this interface.
The default value of the Metric is
Reference Bandwidth / ifSpeed. The value
of the reference bandwidth is configured
by the ospfv3ReferenceBandwidth object."::={ jnxOspfv3IfEntry 19}jnxOspfv3IfLinkScopeLsaCount OBJECT-TYPESYNTAXGauge32MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The total number of Link-Scope link state
advertisements in this link's link state
database."::={ jnxOspfv3IfEntry 20}jnxOspfv3IfLinkLsaCksumSum OBJECT-TYPESYNTAXInteger32MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The 32-bit unsigned sum of the Link-Scope link state
advertisements' LS checksums contained in this
link's link state database. The sum can be used
to determine if there has been a change in a
router's link state database, and to compare the
link state database of two routers."::={ jnxOspfv3IfEntry 21}jnxOspfv3IfDemandNbrProbe OBJECT-TYPESYNTAXTruthValueMAX-ACCESSread-createSTATUScurrentDESCRIPTION"Indicates whether or not neighbor probing is
enabled to determine whether or not the neighbor
is inactive. Neighbor probing is disabled by
default."DEFVAL{ false }::={ jnxOspfv3IfEntry 22}jnxOspfv3IfDemandNbrProbeRetxLimit OBJECT-TYPESYNTAXUnsigned32UNITS"seconds"MAX-ACCESSread-createSTATUScurrentDESCRIPTION"The number of consecutive LSA retransmissions before
the neighbor is deemed inactive and the neighbor
adjacency is brought down."DEFVAL{10}::={ jnxOspfv3IfEntry 23}jnxOspfv3IfDemandNbrProbeInterval OBJECT-TYPESYNTAXUnsigned32UNITS"seconds"MAX-ACCESSread-createSTATUScurrentDESCRIPTION"Defines how often the neighbor will be probed."DEFVAL{120}::={ jnxOspfv3IfEntry 24}-- OSPFv3 Virtual Interface Table-- The Virtual Interface Table describes the virtual-- links that the OSPFv3 Process is configured to-- carry on.jnxOspfv3VirtIfTable OBJECT-TYPESYNTAXSEQUENCEOF JnxOspfv3VirtIfEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"Information about this router's virtual
interfaces."REFERENCE"OSPF Version 2, Appendix C.4 Virtual link
parameters"::={ jnxOspfv3Objects 8}jnxOspfv3VirtIfEntry OBJECT-TYPESYNTAX JnxOspfv3VirtIfEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"Information about a single Virtual Interface."INDEX{ jnxOspfv3VirtIfAreaId,
jnxOspfv3VirtIfNeighbor }::={ jnxOspfv3VirtIfTable 1}
JnxOspfv3VirtIfEntry ::=SEQUENCE{
jnxOspfv3VirtIfAreaId
JnxOspfv3AreaIdTc,
jnxOspfv3VirtIfNeighbor
JnxOspfv3RouterIdTc,
jnxOspfv3VirtIfIndex
InterfaceIndex,
jnxOspfv3VirtIfInstId
JnxOspfv3IfInstIdTc,
jnxOspfv3VirtIfTransitDelay
JnxOspfv3UpToRefreshIntervalTc,
jnxOspfv3VirtIfRetransInterval
JnxOspfv3UpToRefreshIntervalTc,
jnxOspfv3VirtIfHelloInterval
HelloRange,
jnxOspfv3VirtIfRtrDeadInterval
JnxOspfv3DeadIntRangeTc,
jnxOspfv3VirtIfState
INTEGER,
jnxOspfv3VirtIfEvents
Counter32,
jnxOspfv3VirtIfStatus
RowStatus,
jnxOspfv3VirtIfLinkScopeLsaCount
Gauge32,
jnxOspfv3VirtIfLinkLsaCksumSum
Integer32}jnxOspfv3VirtIfAreaId OBJECT-TYPESYNTAX JnxOspfv3AreaIdTc
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"The Transit Area that the Virtual Link
traverses. By definition, this is not
Area 0"::={ jnxOspfv3VirtIfEntry 1}jnxOspfv3VirtIfNeighbor OBJECT-TYPESYNTAX JnxOspfv3RouterIdTc
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"The Router ID of the Virtual Neighbor."::={ jnxOspfv3VirtIfEntry 2}jnxOspfv3VirtIfIndex OBJECT-TYPESYNTAXInterfaceIndexMAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The local interface index assigned to this
OSPFv3 virtual interface. It is advertised in
Hello's sent over the virtal link and in the
router's router-LSAs."::={ jnxOspfv3VirtIfEntry 3}jnxOspfv3VirtIfInstId OBJECT-TYPESYNTAX JnxOspfv3IfInstIdTc
MAX-ACCESSread-createSTATUScurrentDESCRIPTION"Specifies the interface instance ID to be used
for the virtual interface. This ID has local link
significance only."DEFVAL{0}::={ jnxOspfv3VirtIfEntry 4}jnxOspfv3VirtIfTransitDelay OBJECT-TYPESYNTAX JnxOspfv3UpToRefreshIntervalTc
UNITS"seconds"MAX-ACCESSread-createSTATUScurrentDESCRIPTION"The estimated number of seconds it takes to
transmit a link state update packet over this
interface."DEFVAL{1}::={ jnxOspfv3VirtIfEntry 5}jnxOspfv3VirtIfRetransInterval OBJECT-TYPESYNTAX JnxOspfv3UpToRefreshIntervalTc
UNITS"seconds"MAX-ACCESSread-createSTATUScurrentDESCRIPTION"The number of seconds between link state
advertisement retransmissions, for adjacencies
belonging to this interface. This value is
also used when retransmitting database
description and link state request packets. This
value should be well over the expected
round-trip time."DEFVAL{5}::={ jnxOspfv3VirtIfEntry 6}jnxOspfv3VirtIfHelloInterval OBJECT-TYPESYNTAXHelloRangeUNITS"seconds"MAX-ACCESSread-createSTATUScurrentDESCRIPTION"The length of time, in seconds, between the
Hello packets that the router sends on the
interface. This value must be the same for the
virtual neighbor."DEFVAL{10}::={ jnxOspfv3VirtIfEntry 7}jnxOspfv3VirtIfRtrDeadInterval OBJECT-TYPESYNTAX JnxOspfv3DeadIntRangeTc
UNITS"seconds"MAX-ACCESSread-createSTATUScurrentDESCRIPTION"The number of seconds that a router's Hello
packets have not been seen before its
neighbors declare the router down. This should
be some multiple of the Hello interval. This
value must be the same for the virtual
neighbor."DEFVAL{60}::={ jnxOspfv3VirtIfEntry 8}jnxOspfv3VirtIfState OBJECT-TYPESYNTAXINTEGER{down(1),pointToPoint(4)}MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"ospf virtual interface states. The same encoding
as the ospfV3IfTable is used."::={ jnxOspfv3VirtIfEntry 9}jnxOspfv3VirtIfEvents OBJECT-TYPESYNTAXCounter32MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The number of state changes or error events on
this Virtual Link"::={ jnxOspfv3VirtIfEntry 10}jnxOspfv3VirtIfStatus OBJECT-TYPESYNTAXRowStatusMAX-ACCESSread-createSTATUScurrentDESCRIPTION"This object permits management of the table by
facilitating actions such as row creation,
construction and destruction.
The value of this object has no effect on
whether other objects in this conceptual row can be
modified."::={ jnxOspfv3VirtIfEntry 11}jnxOspfv3VirtIfLinkScopeLsaCount OBJECT-TYPESYNTAXGauge32MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The total number of Link-Scope link state
advertisements in this virtual link's link state
database."::={ jnxOspfv3VirtIfEntry 12}jnxOspfv3VirtIfLinkLsaCksumSum OBJECT-TYPESYNTAXInteger32MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The 32-bit unsigned sum of the Link-Scope link-state
advertisements' LS checksums contained in this
virtual link's link-state database. The sum can be used
to determine if there has been a change in a
router's link state database, and to compare the
link state database of two routers."::={ jnxOspfv3VirtIfEntry 13}-- OSPFv3 Neighbor Table-- The OSPFv3 Neighbor Table describes all neighbors in-- the locality of the subject router.jnxOspfv3NbrTable OBJECT-TYPESYNTAXSEQUENCEOF JnxOspfv3NbrEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"A table of non-virtual neighbor information."REFERENCE"OSPF Version 2, Section 10 The Neighbor Data
Structure"::={ jnxOspfv3Objects 9}jnxOspfv3NbrEntry OBJECT-TYPESYNTAX JnxOspfv3NbrEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"The information regarding a single neighbor."REFERENCE"OSPF Version 2, Section 10 The Neighbor Data
Structure"INDEX{ jnxOspfv3NbrIfIndex,
jnxOspfv3NbrIfInstId,
jnxOspfv3NbrRtrId }::={ jnxOspfv3NbrTable 1}
JnxOspfv3NbrEntry ::=SEQUENCE{
jnxOspfv3NbrIfIndex
InterfaceIndex,
jnxOspfv3NbrIfInstId
JnxOspfv3IfInstIdTc,
jnxOspfv3NbrRtrId
JnxOspfv3RouterIdTc,
jnxOspfv3NbrAddressType
InetAddressType,
jnxOspfv3NbrAddress
InetAddress,
jnxOspfv3NbrOptions
Integer32,
jnxOspfv3NbrPriority
DesignatedRouterPriority,
jnxOspfv3NbrState
INTEGER,
jnxOspfv3NbrEvents
Counter32,
jnxOspfv3NbrLsRetransQLen
Gauge32,
jnxOspfv3NbrHelloSuppressed
TruthValue,
jnxOspfv3NbrIfId
InterfaceIndex,
jnxOspfv3NbrRestartHelperStatus
INTEGER,
jnxOspfv3NbrRestartHelperAge
JnxOspfv3UpToRefreshIntervalTc,
jnxOspfv3NbrRestartHelperExitRc
INTEGER}jnxOspfv3NbrIfIndex OBJECT-TYPESYNTAXInterfaceIndexMAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"The local link ID of the link over which the
neighbor can be reached."::={ jnxOspfv3NbrEntry 1}jnxOspfv3NbrIfInstId OBJECT-TYPESYNTAX JnxOspfv3IfInstIdTc
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"Interface instance over which the neighbor
can be reached. This ID has local link
significance only."::={ jnxOspfv3NbrEntry 2}jnxOspfv3NbrRtrId OBJECT-TYPESYNTAX JnxOspfv3RouterIdTc
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"A 32-bit integer uniquely identifying the neighboring
router in the Autonomous System."::={ jnxOspfv3NbrEntry 3}jnxOspfv3NbrAddressType OBJECT-TYPESYNTAXInetAddressTypeMAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The address type of ospfv3NbrAddress. Only IPv6
addresses without zone index are expected."::={ jnxOspfv3NbrEntry 4}jnxOspfv3NbrAddress OBJECT-TYPESYNTAXInetAddress(SIZE(16))MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The IPv6 address of the neighbor associated with
the local link."::={ jnxOspfv3NbrEntry 5}jnxOspfv3NbrOptions OBJECT-TYPESYNTAXInteger32MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"A Bit Mask corresponding to the neighbor's
options field."REFERENCE"OSPF Version 3, Appendix A.2 the Options field"::={ jnxOspfv3NbrEntry 6}jnxOspfv3NbrPriority OBJECT-TYPESYNTAXDesignatedRouterPriorityMAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The priority of this neighbor in the designated
router election algorithm. The value 0 signifies
that the neighbor is not eligible to become the
designated router on this particular network."::={ jnxOspfv3NbrEntry 7}jnxOspfv3NbrState OBJECT-TYPESYNTAXINTEGER{down(1),attempt(2),init(3),twoWay(4),exchangeStart(5),exchange(6),loading(7),full(8)}MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The State of the relationship with this
Neighbor."REFERENCE"OSPF Version 2, Section 10.1 Neighbor States"::={ jnxOspfv3NbrEntry 8}jnxOspfv3NbrEvents OBJECT-TYPESYNTAXCounter32MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The number of times this neighbor relationship
has changed state, or an error has occurred."::={ jnxOspfv3NbrEntry 9}jnxOspfv3NbrLsRetransQLen OBJECT-TYPESYNTAXGauge32MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The current length of the retransmission
queue."::={ jnxOspfv3NbrEntry 10}jnxOspfv3NbrHelloSuppressed OBJECT-TYPESYNTAXTruthValueMAX-ACCESSread-onlySTATUScurrentDESCRIPTION"Indicates whether Hellos are being suppressed
to the neighbor"::={ jnxOspfv3NbrEntry 11}jnxOspfv3NbrIfId OBJECT-TYPESYNTAXInterfaceIndexMAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The interface ID that the neighbor advertises
in its Hello Packets on this link, that is, the
neighbor's local interface index."::={ jnxOspfv3NbrEntry 12}jnxOspfv3NbrRestartHelperStatus OBJECT-TYPESYNTAXINTEGER{ notHelping (1),helping (2)}MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"Indicates whether the router is acting
as a Graceful restart helper for the neighbor."::={ jnxOspfv3NbrEntry 13}jnxOspfv3NbrRestartHelperAge OBJECT-TYPESYNTAX JnxOspfv3UpToRefreshIntervalTc
UNITS"seconds"MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"Remaining time in current OSPF Graceful restart
interval, if the router is acting as a restart
helper for the neighbor."::={ jnxOspfv3NbrEntry 14}jnxOspfv3NbrRestartHelperExitRc OBJECT-TYPESYNTAXINTEGER{ none (1),inProgress (2),completed (3),timedOut (4),topologyChanged (5)}MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"Describes the outcome of the last attempt at acting
as a Graceful restart helper for the neighbor.
none:............no restart has yet been attempted.
inProgress:......a restart attempt is currently underway.
completed:.......the last restart completed successfully.
timedOut:........the last restart timed out.
topologyChanged:.the last restart was aborted due to
a topology change."::={ jnxOspfv3NbrEntry 15}-- OSPFv3 Configured Neighbor Table-- The OSPFv3 Configured Neighbor Table describes all configured-- neighborsjnxOspfv3CfgNbrTable OBJECT-TYPESYNTAXSEQUENCEOF JnxOspfv3CfgNbrEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"A table of configured, non-virtual neighbor
information."REFERENCE"OSPF Version 2, Section 10 The Neighbor Data
Structure"::={ jnxOspfv3Objects 10}jnxOspfv3CfgNbrEntry OBJECT-TYPESYNTAX JnxOspfv3CfgNbrEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"The information regarding a single configured
neighbor or neighbor discovered by lower-level
protocols such as Inverse Neighbor Discovery."REFERENCE"OSPF Version 2, Section 10 The Neighbor Data
Structure"INDEX{ jnxOspfv3CfgNbrIfIndex,
jnxOspfv3CfgNbrIfInstId,
jnxOspfv3CfgNbrAddressType,
jnxOspfv3CfgNbrAddress }::={ jnxOspfv3CfgNbrTable 1}
JnxOspfv3CfgNbrEntry ::=SEQUENCE{
jnxOspfv3CfgNbrIfIndex
InterfaceIndex,
jnxOspfv3CfgNbrIfInstId
JnxOspfv3IfInstIdTc,
jnxOspfv3CfgNbrAddressType
InetAddressType,
jnxOspfv3CfgNbrAddress
InetAddress,
jnxOspfv3CfgNbrPriority
DesignatedRouterPriority,
jnxOspfv3CfgNbrStatus
RowStatus}jnxOspfv3CfgNbrIfIndex OBJECT-TYPESYNTAXInterfaceIndexMAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"The local link ID of the link over which the
neighbor can be reached."::={ jnxOspfv3CfgNbrEntry 1}jnxOspfv3CfgNbrIfInstId OBJECT-TYPESYNTAX JnxOspfv3IfInstIdTc
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"Interface instance over which the neighbor
can be reached. This ID has local link
significance only."::={ jnxOspfv3CfgNbrEntry 2}jnxOspfv3CfgNbrAddressType OBJECT-TYPESYNTAXInetAddressTypeMAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"The address type of ospfv3NbrAddress. Only IPv6
addresses without zone index are expected."::={ jnxOspfv3CfgNbrEntry 3}jnxOspfv3CfgNbrAddress OBJECT-TYPESYNTAXInetAddress(SIZE(16))MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"The IPv6 address of the neighbor associated with
the local link."::={ jnxOspfv3CfgNbrEntry 4}jnxOspfv3CfgNbrPriority OBJECT-TYPESYNTAXDesignatedRouterPriorityMAX-ACCESSread-createSTATUScurrentDESCRIPTION"The priority of this neighbor in the designated
router election algorithm. The value 0 signifies
that the neighbor is not eligible to become the
designated router on this particular network."DEFVAL{1}::={ jnxOspfv3CfgNbrEntry 5}jnxOspfv3CfgNbrStatus OBJECT-TYPESYNTAXRowStatusMAX-ACCESSread-createSTATUScurrentDESCRIPTION"This object permits management of the table by
facilitating actions such as row creation,
construction and destruction.
The value of this object has no effect on
whether other objects in this conceptual row can be
modified."::={ jnxOspfv3CfgNbrEntry 6}-- jnxOspfv3 Virtual Neighbor Table-- This table describes all virtual neighbors.-- Since Virtual Links are configured in the-- virtual interface table, this table is read-only.jnxOspfv3VirtNbrTable OBJECT-TYPESYNTAXSEQUENCEOF JnxOspfv3VirtNbrEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"A table of virtual neighbor information."REFERENCE"OSPF Version 2, Section 15 Virtual Links"::={ jnxOspfv3Objects 11}jnxOspfv3VirtNbrEntry OBJECT-TYPESYNTAX JnxOspfv3VirtNbrEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"Virtual neighbor information."INDEX{ jnxOspfv3VirtNbrArea,
jnxOspfv3VirtNbrRtrId }::={ jnxOspfv3VirtNbrTable 1}
JnxOspfv3VirtNbrEntry ::=SEQUENCE{
jnxOspfv3VirtNbrArea
JnxOspfv3AreaIdTc,
jnxOspfv3VirtNbrRtrId
JnxOspfv3RouterIdTc,
jnxOspfv3VirtNbrIfIndex
InterfaceIndex,
jnxOspfv3VirtNbrIfInstId
JnxOspfv3IfInstIdTc,
jnxOspfv3VirtNbrAddressType
InetAddressType,
jnxOspfv3VirtNbrAddress
InetAddress,
jnxOspfv3VirtNbrOptions
Integer32,
jnxOspfv3VirtNbrState
INTEGER,
jnxOspfv3VirtNbrEvents
Counter32,
jnxOspfv3VirtNbrLsRetransQLen
Gauge32,
jnxOspfv3VirtNbrHelloSuppressed
TruthValue,
jnxOspfv3VirtNbrIfId
InterfaceIndex,
jnxOspfv3VirtNbrRestartHelperStatus
INTEGER,
jnxOspfv3VirtNbrRestartHelperAge
JnxOspfv3UpToRefreshIntervalTc,
jnxOspfv3VirtNbrRestartHelperExitRc
INTEGER}jnxOspfv3VirtNbrArea OBJECT-TYPESYNTAX JnxOspfv3AreaIdTc
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"The Transit Area Identifier."::={ jnxOspfv3VirtNbrEntry 1}jnxOspfv3VirtNbrRtrId OBJECT-TYPESYNTAX JnxOspfv3RouterIdTc
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"A 32-bit integer uniquely identifying the
neighboring router in the Autonomous System."::={ jnxOspfv3VirtNbrEntry 2}jnxOspfv3VirtNbrIfIndex OBJECT-TYPESYNTAXInterfaceIndexMAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The local interface ID for the virtual link over
which the neighbor can be reached."::={ jnxOspfv3VirtNbrEntry 3}jnxOspfv3VirtNbrIfInstId OBJECT-TYPESYNTAX JnxOspfv3IfInstIdTc
MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The interface instance for the virtual link over
which the neighbor can be reached."::={ jnxOspfv3VirtNbrEntry 4}jnxOspfv3VirtNbrAddressType OBJECT-TYPESYNTAXInetAddressTypeMAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The address type of ospfv3VirtNbrAddress. Only IPv6
addresses without zone index are expected."::={ jnxOspfv3VirtNbrEntry 5}jnxOspfv3VirtNbrAddress OBJECT-TYPESYNTAXInetAddress(SIZE(16))MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The IPv6 address advertised by this Virtual Neighbor.
It must be a Global scope address."::={ jnxOspfv3VirtNbrEntry 6}jnxOspfv3VirtNbrOptions OBJECT-TYPESYNTAXInteger32MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"A Bit Mask corresponding to the neighbor's options
field."REFERENCE"OSPF Version 3, Appendix A.2 the Options field"::={ jnxOspfv3VirtNbrEntry 7}jnxOspfv3VirtNbrState OBJECT-TYPESYNTAXINTEGER{down(1),attempt(2),init(3),twoWay(4),exchangeStart(5),exchange(6),loading(7),full(8)}MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The state of the Virtual Neighbor Relationship."::={ jnxOspfv3VirtNbrEntry 8}jnxOspfv3VirtNbrEvents OBJECT-TYPESYNTAXCounter32MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The number of times this virtual link has
changed its state, or an error has occurred."::={ jnxOspfv3VirtNbrEntry 9}jnxOspfv3VirtNbrLsRetransQLen OBJECT-TYPESYNTAXGauge32MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The current length of the retransmission
queue."::={ jnxOspfv3VirtNbrEntry 10}jnxOspfv3VirtNbrHelloSuppressed OBJECT-TYPESYNTAXTruthValueMAX-ACCESSread-onlySTATUScurrentDESCRIPTION"Indicates whether Hellos are being suppressed
to the neighbor"::={ jnxOspfv3VirtNbrEntry 11}jnxOspfv3VirtNbrIfId OBJECT-TYPESYNTAXInterfaceIndexMAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The interface ID that the neighbor advertises
in its Hello Packets on this virtual link, that is,
the neighbor's local interface ID."::={ jnxOspfv3VirtNbrEntry 12}jnxOspfv3VirtNbrRestartHelperStatus OBJECT-TYPESYNTAXINTEGER{ notHelping (1),helping (2)}MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"Indicates whether the router is acting
as a Graceful restart helper for the neighbor."::={ jnxOspfv3VirtNbrEntry 13}jnxOspfv3VirtNbrRestartHelperAge OBJECT-TYPESYNTAX JnxOspfv3UpToRefreshIntervalTc
UNITS"seconds"MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"Remaining time in current OSPF Graceful restart
interval, if the router is acting as a restart
helper for the neighbor."::={ jnxOspfv3VirtNbrEntry 14}jnxOspfv3VirtNbrRestartHelperExitRc OBJECT-TYPESYNTAXINTEGER{ none (1),inProgress (2),completed (3),timedOut (4),topologyChanged (5)}MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"Describes the outcome of the last attempt at acting
as a Graceful restart helper for the neighbor.
none:............no restart has yet been attempted.
inProgress:......a restart attempt is currently underway.
completed:.......the last restart completed successfully.
timedOut:........the last restart timed out.
topologyChanged:.the last restart was aborted due to
a topology change."::={ jnxOspfv3VirtNbrEntry 15}---- The OSPFv3 Area Aggregate Table--jnxOspfv3AreaAggregateTable OBJECT-TYPESYNTAXSEQUENCEOF JnxOspfv3AreaAggregateEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"A range of IPv6 prefixes specified by a
prefix/prefix length pair. Note that if
ranges are configured such that one range
subsumes another range the most specific
match is the preferred one."::={ jnxOspfv3Objects 12}jnxOspfv3AreaAggregateEntry OBJECT-TYPESYNTAX JnxOspfv3AreaAggregateEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"A range of IPv6 prefixes specified by a
prefix/prefix length pair. Note that if
ranges are configured such that one range
subsumes another range the most specific match is
the preferred one."REFERENCE"OSPF Version 2, Appendix C.2 Area parameters"INDEX{ jnxOspfv3AreaAggregateAreaID,
jnxOspfv3AreaAggregateAreaLsdbType,
jnxOspfv3AreaAggregatePrefixType,
jnxOspfv3AreaAggregatePrefix,
jnxOspfv3AreaAggregatePrefixLength }::={ jnxOspfv3AreaAggregateTable 1}
JnxOspfv3AreaAggregateEntry ::=SEQUENCE{
jnxOspfv3AreaAggregateAreaID
JnxOspfv3AreaIdTc,
jnxOspfv3AreaAggregateAreaLsdbType
INTEGER,
jnxOspfv3AreaAggregatePrefixType
InetAddressType,
jnxOspfv3AreaAggregatePrefix
InetAddress,
jnxOspfv3AreaAggregatePrefixLength
InetAddressPrefixLength,
jnxOspfv3AreaAggregateStatus
RowStatus,
jnxOspfv3AreaAggregateEffect
INTEGER,
jnxOspfv3AreaAggregateRouteTag
INTEGER}jnxOspfv3AreaAggregateAreaID OBJECT-TYPESYNTAX JnxOspfv3AreaIdTc
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"The Area the Address Aggregate is to be found
within."REFERENCE"OSPF Version 2, Appendix C.2 Area parameters"::={ jnxOspfv3AreaAggregateEntry 1}jnxOspfv3AreaAggregateAreaLsdbType OBJECT-TYPESYNTAXINTEGER{interAreaPrefixLsa(8195),-- 0x2003nssaExternalLsa(8199)-- 0x2007
}MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"The type of the Address Aggregate. This field
specifies the Area Lsdb type that this Address
Aggregate applies to."REFERENCE"OSPF Version 2, Appendix A.4.1 The Link State
Advertisement header"::={ jnxOspfv3AreaAggregateEntry 2}jnxOspfv3AreaAggregatePrefixType OBJECT-TYPESYNTAXInetAddressTypeMAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"The prefix type of ospfv3AreaAggregatePrefix. Only
IPv6 addresses are expected."::={ jnxOspfv3AreaAggregateEntry 4}jnxOspfv3AreaAggregatePrefix OBJECT-TYPESYNTAXInetAddress(SIZE(0..16))MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"The IPv6 Prefix."REFERENCE"OSPF Version 2, Appendix C.2 Area parameters"::={ jnxOspfv3AreaAggregateEntry 5}jnxOspfv3AreaAggregatePrefixLength OBJECT-TYPESYNTAXInetAddressPrefixLength(3..128)UNITS"bits"MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"The length of the prefix (in bits). A prefix can
not be shorter than 3 bits."REFERENCE"OSPF Version 2, Appendix C.2 Area parameters"::={ jnxOspfv3AreaAggregateEntry 6}jnxOspfv3AreaAggregateStatus OBJECT-TYPESYNTAXRowStatusMAX-ACCESSread-createSTATUScurrentDESCRIPTION"This object permits management of the table by
facilitating actions such as row creation,
construction and destruction.
The value of this object has no effect on
whether other objects in this conceptual row can be
modified."::={ jnxOspfv3AreaAggregateEntry 7}jnxOspfv3AreaAggregateEffect OBJECT-TYPESYNTAXINTEGER{advertiseMatching(1),doNotAdvertiseMatching(2)}MAX-ACCESSread-createSTATUScurrentDESCRIPTION"Prefixes subsumed by ranges either trigger the
advertisement of the indicated aggregate
(advertiseMatching), or result in the prefix not
being advertised at all outside the area."DEFVAL{ advertiseMatching }::={ jnxOspfv3AreaAggregateEntry 8}jnxOspfv3AreaAggregateRouteTag OBJECT-TYPESYNTAXINTEGERMAX-ACCESSread-createSTATUScurrentDESCRIPTION"This tag is advertised only in the summarized
As-External LSA when summarizing from NSSA-LSA's to
AS-External-LSA's."DEFVAL{0}::={ jnxOspfv3AreaAggregateEntry 9}-- The jnxOspfv3 Notification Table-- The jnxOspfv3 Notification Table records fields that are-- required for notificationsjnxOspfv3NotificationEntry OBJECTIDENTIFIER::={ jnxOspfv3Objects 13}jnxOspfv3ConfigErrorType OBJECT-TYPESYNTAXINTEGER{badVersion (1),areaMismatch (2),unknownNbmaNbr (3),-- Router is DR eligibleunknownVirtualNbr (4),helloIntervalMismatch (5),deadIntervalMismatch (6),optionMismatch (7),mtuMismatch (8),duplicateRouterId (9),noError (10)}MAX-ACCESSaccessible-for-notifySTATUScurrentDESCRIPTION"Potential types of configuration conflicts.
Used by the ospfv3ConfigError and
ospfv3ConfigVirtError notifications. When the last value
of a notification using this object is needed, but no
notifications of that type have been sent, this value
pertaining to this object should be returned as
noError"::={ jnxOspfv3NotificationEntry 1}jnxOspfv3PacketType OBJECT-TYPESYNTAXINTEGER{hello (1),dbDescript (2),lsReq (3),lsUpdate (4),lsAck (5),nullPacket (6)}MAX-ACCESSaccessible-for-notifySTATUScurrentDESCRIPTION"OSPFv3 packet types. When the last value of a notification
using this object is needed, but no notifications of
that type have been sent, the value pertaining
to this object should be returned as nullPacket"::={ jnxOspfv3NotificationEntry 2}jnxOspfv3PacketSrc OBJECT-TYPESYNTAXInetAddressMAX-ACCESSaccessible-for-notifySTATUScurrentDESCRIPTION"The IPv6 address of an inbound packet that cannot
be identified by a neighbor instance. When
the last value of a notification using this object is
needed, but no notifications of that type have been sent,
the value pertaining to this object should
be returned as 0
Only IPv6 addresses without zone index are expected."::={ jnxOspfv3NotificationEntry 3}-- Notification definitionsjnxOspfv3VirtIfStateChange NOTIFICATION-TYPEOBJECTS{ jnxOspfv3RouterId,-- The originator of the notification
jnxOspfv3VirtIfState -- The new state}STATUScurrentDESCRIPTION"An ospfv3VirtIfStateChange notification signifies that there
has been a change in the state of an OSPFv3 virtual
interface.
This notification should be generated when the interface
state regresses (e.g., goes from Point-to-Point to Down)
or progresses to a terminal state (i.e., Point-to-Point)."::={ jnxOspfv3Notifications 1}jnxOspfv3NbrStateChange NOTIFICATION-TYPEOBJECTS{ jnxOspfv3RouterId,-- The originator of-- the notification
jnxOspfv3NbrState -- The new state}STATUScurrentDESCRIPTION"An ospfv3NbrStateChange notification signifies that
there has been a change in the state of a
non-virtual OSPFv3 neighbor. This notification should be
generated when the neighbor state regresses
(e.g., goes from Attempt or Full to 1-Way or
Down) or progresses to a terminal state (e.g.,
2-Way or Full). When an neighbor transitions
from or to Full on non-broadcast multi-access
and broadcast networks, the notification should be
generated by the designated router. A designated
router transitioning to Down will be noted by
ospfIfStateChange."::={ jnxOspfv3Notifications 2}jnxOspfv3VirtNbrStateChange NOTIFICATION-TYPEOBJECTS{ jnxOspfv3RouterId,-- The originator of the notification
jnxOspfv3VirtNbrState -- The new state}STATUScurrentDESCRIPTION"An ospfv3VirtNbrStateChange notification signifies
that there has been a change in the state of an OSPFv3
virtual neighbor. This notification should be generated
when the neighbor state regresses (e.g., goes
from Attempt or Full to 1-Way or Down) or
progresses to a terminal state (e.g., Full)."::={ jnxOspfv3Notifications 3}jnxOspfv3IfConfigError NOTIFICATION-TYPEOBJECTS{ jnxOspfv3RouterId,-- The originator of the notification
jnxOspfv3IfState,-- State of the interface
jnxOspfv3PacketSrc,-- IPv6 address of source
jnxOspfv3ConfigErrorType,-- Type of error
jnxOspfv3PacketType -- Type of packet}STATUScurrentDESCRIPTION"An ospfv3IfConfigError notification signifies that a
packet has been received on a non-virtual
interface from a router whose configuration
parameters conflict with this router's
configuration parameters. Note that the event
optionMismatch should cause a notification only if it
prevents an adjacency from forming."::={ jnxOspfv3Notifications 4}jnxOspfv3VirtIfConfigError NOTIFICATION-TYPEOBJECTS{ jnxOspfv3RouterId,-- The originator of the notification
jnxOspfv3VirtIfState,-- State of the interface
jnxOspfv3ConfigErrorType,-- Type of error
jnxOspfv3PacketType
}STATUScurrentDESCRIPTION"An ospfv3VirtIfConfigError notification signifies that a
packet has been received on a virtual interface
from a router whose configuration parameters
conflict with this router's configuration
parameters. Note that the event optionMismatch
should cause a notification only if it prevents an
adjacency from forming."::={ jnxOspfv3Notifications 5}jnxOspfv3IfRxBadPacket NOTIFICATION-TYPEOBJECTS{ jnxOspfv3RouterId,-- The originator of the notification
jnxOspfv3IfState,-- State of the interface
jnxOspfv3PacketSrc,-- The source IPv6 address
jnxOspfv3PacketType -- Type of packet}STATUScurrentDESCRIPTION"An ospfv3IfRxBadPacket notification signifies that an
ospfv3 packet that cannot be parsed has been received on a
non-virtual interface."::={ jnxOspfv3Notifications 6}jnxOspfv3VirtIfRxBadPacket NOTIFICATION-TYPEOBJECTS{ jnxOspfv3RouterId,-- The originator of the notification
jnxOspfv3VirtIfState,-- State of the interface
jnxOspfv3PacketType -- Type of packet}STATUScurrentDESCRIPTION"An ospfv3VirtIfRxBadPacket notification signifies
that an OSPFv3 packet that cannot be parsed has been received
on a virtual interface."::={ jnxOspfv3Notifications 7}jnxOspfv3LsdbOverflow NOTIFICATION-TYPEOBJECTS{ jnxOspfv3RouterId,-- The originator of the notification
jnxOspfv3ExtAreaLsdbLimit -- Limit on External LSAs}STATUScurrentDESCRIPTION"An ospfv3LsdbOverflow notification signifies that the
number of LSAs in the router's link-state
database has exceeded ospfv3ExtAreaLsdbLimit."::={ jnxOspfv3Notifications 8}jnxOspfv3LsdbApproachingOverflow NOTIFICATION-TYPEOBJECTS{ jnxOspfv3RouterId,-- The originator of the notification
jnxOspfv3ExtAreaLsdbLimit
}STATUScurrentDESCRIPTION"An ospfv3LsdbApproachingOverflow notification signifies
that the number of LSAs in the router's
link-state database has exceeded ninety percent of
ospfv3ExtAreaLsdbLimit."::={ jnxOspfv3Notifications 9}jnxOspfv3IfStateChange NOTIFICATION-TYPEOBJECTS{ jnxOspfv3RouterId,-- The originator of the notification
jnxOspfv3IfState -- The new state}STATUScurrentDESCRIPTION"An ospfv3IfStateChange notification signifies that there
has been a change in the state of a non-virtual
OSPFv3 interface. This notification should be generated
when the interface state regresses (e.g., goes
from Dr to Down) or progresses to a terminal
state (i.e., Point-to-Point, DR Other, Dr, or
Backup)."::={ jnxOspfv3Notifications 10}jnxOspfv3NssaTranslatorStatusChange NOTIFICATION-TYPEOBJECTS{ jnxOspfv3RouterId,-- The originator of the notification
jnxOspfv3AreaNssaTranslatorState -- new state}STATUScurrentDESCRIPTION"An ospfv3NssaTranslatorStatusChange notification
indicates that there has been a change in the router's
ability to translate OSPFv3 NSSA LSAs into OSPFv3 External
LSAs. This notification should be generated when the
Translator Status transitions from or to any defined
status on a per area basis."::={ jnxOspfv3Notifications 11}jnxOspfv3RestartStatusChange NOTIFICATION-TYPEOBJECTS{ jnxOspfv3RouterId,-- The originator of the notification
jnxOspfv3RestartStatus,-- new status
jnxOspfv3RestartInterval,
jnxOspfv3RestartExitRc
}STATUScurrentDESCRIPTION"An ospfv3RestartStatusChange notification signifies that
there has been a change in the graceful restart
state for the router. This notification should be
generated when the router restart status
changes."::={ jnxOspfv3Notifications 12}jnxOspfv3NbrRestartHelperStatusChange NOTIFICATION-TYPEOBJECTS{ jnxOspfv3RouterId,-- The originator of the notification
jnxOspfv3NbrRestartHelperStatus,-- new status
jnxOspfv3NbrRestartHelperAge,
jnxOspfv3NbrRestartHelperExitRc
}STATUScurrentDESCRIPTION"An ospfv3NbrRestartHelperStatusChange notification
signifies that there has been a change in the
graceful restart helper state for the neighbor.
This notification should be generated when the
neighbor restart helper status transitions for a neighbor."::={ jnxOspfv3Notifications 13}jnxOspfv3VirtNbrRestartHelperStatusChange NOTIFICATION-TYPEOBJECTS{ jnxOspfv3RouterId,-- The originator of the notification
jnxOspfv3VirtNbrRestartHelperStatus,-- new status
jnxOspfv3VirtNbrRestartHelperAge,
jnxOspfv3VirtNbrRestartHelperExitRc
}STATUScurrentDESCRIPTION"An ospfv3VirtNbrRestartHelperStatusChange
notification signifies that there has been a
change in the graceful restart helper state for
the virtual neighbor. This notification should be
generated when the virtual neighbor restart helper status
transitions for a virtual neighbor."::={ jnxOspfv3Notifications 14}-- conformance informationjnxOspfv3Groups OBJECTIDENTIFIER::={ jnxOspfv3Conformance 1}jnxOspfv3Compliances OBJECTIDENTIFIER::={ jnxOspfv3Conformance 2}-- compliance statementsjnxOspfv3Compliance MODULE-COMPLIANCESTATUScurrentDESCRIPTION"The compliance statement"MODULE-- this moduleMANDATORY-GROUPS{
jnxOspfv3BasicGroup,
jnxOspfv3AreaGroup,
jnxOspfv3IfGroup,
jnxOspfv3VirtIfGroup,
jnxOspfv3NbrGroup,
jnxOspfv3CfgNbrGroup,
jnxOspfv3VirtNbrGroup,
jnxOspfv3AreaAggregateGroup,
jnxOspfv3NotificationObjectGroup,
jnxOspfv3NotificationGroup
}GROUP jnxOspfv3AsLsdbGroup
DESCRIPTION"This group is required for OSPFv3 systems that
display their AS-scope link state database."GROUP jnxOspfv3AreaLsdbGroup
DESCRIPTION"This group is required for OSPFv3 systems that
display their Area-scope link state database."GROUP jnxOspfv3LinkLsdbGroup
DESCRIPTION"This group is required for OSPFv3 systems that
display their Link-scope link state database."GROUP jnxOspfv3HostGroup
DESCRIPTION"This group is required for OSPFv3 systems that
support attached hosts."OBJECT jnxOspfv3NbrAddressType
SYNTAXInetAddressType{ ipv6(2)}DESCRIPTION"An implementation is only required to support IPv6
address without zone index."OBJECT jnxOspfv3VirtNbrAddressType
SYNTAXInetAddressType{ ipv6(2)}DESCRIPTION"An implementation is only required to support IPv6
address without zone index."::={ jnxOspfv3Compliances 1}-- units of conformancejnxOspfv3BasicGroup OBJECT-GROUPOBJECTS{
jnxOspfv3RouterId,
jnxOspfv3AdminStat,
jnxOspfv3VersionNumber,
jnxOspfv3AreaBdrRtrStatus,
jnxOspfv3ASBdrRtrStatus,
jnxOspfv3AsScopeLsaCount,
jnxOspfv3AsScopeLsaCksumSum,
jnxOspfv3OriginateNewLsas,
jnxOspfv3RxNewLsas,
jnxOspfv3ExtLsaCount,
jnxOspfv3ExtAreaLsdbLimit,
jnxOspfv3MulticastExtensions,
jnxOspfv3ExitOverflowInterval,
jnxOspfv3DemandExtensions,
jnxOspfv3ReferenceBandwidth,
jnxOspfv3RestartSupport,
jnxOspfv3RestartInterval,
jnxOspfv3RestartStatus,
jnxOspfv3RestartAge,
jnxOspfv3RestartExitRc,
jnxOspfv3NotificationEnable
}STATUScurrentDESCRIPTION"These objects are used for managing/monitoring
OSPFv3 global parameters."::={ jnxOspfv3Groups 1}jnxOspfv3AreaGroup OBJECT-GROUPOBJECTS{
jnxOspfv3ImportAsExtern,
jnxOspfv3AreaSpfRuns,
jnxOspfv3AreaBdrRtrCount,
jnxOspfv3AreaAsBdrRtrCount,
jnxOspfv3AreaScopeLsaCount,
jnxOspfv3AreaScopeLsaCksumSum,
jnxOspfv3AreaSummary,
jnxOspfv3AreaStatus,
jnxOspfv3StubMetric,
jnxOspfv3AreaNssaTranslatorRole,
jnxOspfv3AreaNssaTranslatorState,
jnxOspfv3AreaNssaTranslatorStabInt,
jnxOspfv3AreaNssaTranslatorEvents,
jnxOspfv3AreaStubMetricType
}STATUScurrentDESCRIPTION"These objects are used for ospfv3 systems
supporting areas."::={ jnxOspfv3Groups 2}jnxOspfv3AsLsdbGroup OBJECT-GROUPOBJECTS{
jnxOspfv3AsLsdbSequence,
jnxOspfv3AsLsdbAge,
jnxOspfv3AsLsdbChecksum,
jnxOspfv3AsLsdbAdvertisement,
jnxOspfv3AsLsdbTypeKnown
}STATUScurrentDESCRIPTION"These objects are used for ospfv3 systems
that display their AS-scope link state database."::={ jnxOspfv3Groups 3}jnxOspfv3AreaLsdbGroup OBJECT-GROUPOBJECTS{
jnxOspfv3AreaLsdbSequence,
jnxOspfv3AreaLsdbAge,
jnxOspfv3AreaLsdbChecksum,
jnxOspfv3AreaLsdbAdvertisement,
jnxOspfv3AreaLsdbTypeKnown
}STATUScurrentDESCRIPTION"These objects are used for OSPFv3 systems
that display their Area-scope link state database."::={ jnxOspfv3Groups 4}jnxOspfv3LinkLsdbGroup OBJECT-GROUPOBJECTS{
jnxOspfv3LinkLsdbSequence,
jnxOspfv3LinkLsdbAge,
jnxOspfv3LinkLsdbChecksum,
jnxOspfv3LinkLsdbAdvertisement,
jnxOspfv3LinkLsdbTypeKnown
}STATUScurrentDESCRIPTION"These objects are used for OSPFv3 systems
that display their Link-scope link state database."::={ jnxOspfv3Groups 5}jnxOspfv3HostGroup OBJECT-GROUPOBJECTS{
jnxOspfv3HostMetric,
jnxOspfv3HostStatus,
jnxOspfv3HostAreaID
}STATUScurrentDESCRIPTION"These objects are used for OSPFv3 systems
that support attached hosts."::={ jnxOspfv3Groups 6}jnxOspfv3IfGroup OBJECT-GROUPOBJECTS{
jnxOspfv3IfAreaId,
jnxOspfv3IfType,
jnxOspfv3IfAdminStat,
jnxOspfv3IfRtrPriority,
jnxOspfv3IfTransitDelay,
jnxOspfv3IfRetransInterval,
jnxOspfv3IfHelloInterval,
jnxOspfv3IfRtrDeadInterval,
jnxOspfv3IfPollInterval,
jnxOspfv3IfState,
jnxOspfv3IfDesignatedRouter,
jnxOspfv3IfBackupDesignatedRouter,
jnxOspfv3IfEvents,
jnxOspfv3IfStatus,
jnxOspfv3IfMulticastForwarding,
jnxOspfv3IfDemand,
jnxOspfv3IfMetricValue,
jnxOspfv3IfLinkScopeLsaCount,
jnxOspfv3IfLinkLsaCksumSum,
jnxOspfv3IfDemandNbrProbe,
jnxOspfv3IfDemandNbrProbeRetxLimit,
jnxOspfv3IfDemandNbrProbeInterval
}STATUScurrentDESCRIPTION"These interface objects used for
managing/monitoring OSPFv3 interfaces."::={ jnxOspfv3Groups 7}jnxOspfv3VirtIfGroup OBJECT-GROUPOBJECTS{
jnxOspfv3VirtIfIndex,
jnxOspfv3VirtIfInstId,
jnxOspfv3VirtIfTransitDelay,
jnxOspfv3VirtIfRetransInterval,
jnxOspfv3VirtIfHelloInterval,
jnxOspfv3VirtIfRtrDeadInterval,
jnxOspfv3VirtIfState,
jnxOspfv3VirtIfEvents,
jnxOspfv3VirtIfStatus,
jnxOspfv3VirtIfLinkScopeLsaCount,
jnxOspfv3VirtIfLinkLsaCksumSum
}STATUScurrentDESCRIPTION"These virtual interface objects are used for
managing/monitoring OSPFv3 virtual interfaces."::={ jnxOspfv3Groups 8}jnxOspfv3NbrGroup OBJECT-GROUPOBJECTS{
jnxOspfv3NbrAddressType,
jnxOspfv3NbrAddress,
jnxOspfv3NbrOptions,
jnxOspfv3NbrPriority,
jnxOspfv3NbrState,
jnxOspfv3NbrEvents,
jnxOspfv3NbrLsRetransQLen,
jnxOspfv3NbrHelloSuppressed,
jnxOspfv3NbrIfId,
jnxOspfv3NbrRestartHelperStatus,
jnxOspfv3NbrRestartHelperAge,
jnxOspfv3NbrRestartHelperExitRc
}STATUScurrentDESCRIPTION"These neighbor objects are used for
managing/monitoring OSPFv3 neighbors."::={ jnxOspfv3Groups 9}jnxOspfv3CfgNbrGroup OBJECT-GROUPOBJECTS{
jnxOspfv3CfgNbrPriority,
jnxOspfv3CfgNbrStatus
}STATUScurrentDESCRIPTION"These configured neighbor objects are used for
managing/monitoring ospfv3 configured neighbors."::={ jnxOspfv3Groups 10}jnxOspfv3VirtNbrGroup OBJECT-GROUPOBJECTS{
jnxOspfv3VirtNbrIfIndex,
jnxOspfv3VirtNbrIfInstId,
jnxOspfv3VirtNbrAddressType,
jnxOspfv3VirtNbrAddress,
jnxOspfv3VirtNbrOptions,
jnxOspfv3VirtNbrState,
jnxOspfv3VirtNbrEvents,
jnxOspfv3VirtNbrLsRetransQLen,
jnxOspfv3VirtNbrHelloSuppressed,
jnxOspfv3VirtNbrIfId,
jnxOspfv3VirtNbrRestartHelperStatus,
jnxOspfv3VirtNbrRestartHelperAge,
jnxOspfv3VirtNbrRestartHelperExitRc
}STATUScurrentDESCRIPTION"These virtual neighbor objects are used for
managing/monitoring OSPFv3 virtual neighbors."::={ jnxOspfv3Groups 11}jnxOspfv3AreaAggregateGroup OBJECT-GROUPOBJECTS{
jnxOspfv3AreaAggregateStatus,
jnxOspfv3AreaAggregateEffect,
jnxOspfv3AreaAggregateRouteTag
}STATUScurrentDESCRIPTION"These area aggregate objects used required for
aggregating OSPFv3 prefixes for summarization
across areas."::={ jnxOspfv3Groups 12}jnxOspfv3NotificationObjectGroup OBJECT-GROUPOBJECTS{
jnxOspfv3ConfigErrorType,
jnxOspfv3PacketType,
jnxOspfv3PacketSrc
}STATUScurrentDESCRIPTION"These objects are used to record notification
parameters"::={ jnxOspfv3Groups 13}jnxOspfv3NotificationGroup NOTIFICATION-GROUPNOTIFICATIONS{
jnxOspfv3VirtIfStateChange,
jnxOspfv3NbrStateChange,
jnxOspfv3VirtNbrStateChange,
jnxOspfv3IfConfigError,
jnxOspfv3VirtIfConfigError,
jnxOspfv3IfRxBadPacket,
jnxOspfv3VirtIfRxBadPacket,
jnxOspfv3LsdbOverflow,
jnxOspfv3LsdbApproachingOverflow,
jnxOspfv3IfStateChange,
jnxOspfv3NssaTranslatorStatusChange,
jnxOspfv3RestartStatusChange,
jnxOspfv3NbrRestartHelperStatusChange,
jnxOspfv3VirtNbrRestartHelperStatusChange
}STATUScurrentDESCRIPTION"This group is used for OSPFv3 notifications"::={ jnxOspfv3Groups 14}END--
-- Copyright (C) The Internet Society (2006).
--
-- This document is subject to the rights, licenses and restrictions
-- contained in BCP 78, and except as set forth therein, the authors
-- retain all their rights.
--
-- This document and the information contained herein are provided on an
-- "AS IS" basis and THE CONTRIBUTOR, THE ORGANIZATION HE/SHE REPRESENTS
-- OR IS SPONSORED BY (IF ANY), THE INTERNET SOCIETY AND THE INTERNET
-- ENGINEERING TASK FORCE DISCLAIM ALL WARRANTIES, EXPRESS OR IMPLIED,
-- INCLUDING BUT NOT LIMITED TO ANY WARRANTY THAT THE USE OF THE
-- INFORMATION HEREIN WILL NOT INFRINGE ANY RIGHTS OR ANY IMPLIED
-- WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.
--
--